backy2 homepage: http://backy2.com/
What is backy2?¶
backy2 is a deduplicating block based backup software which encrypts and compresses by default.
The primary usecases for backy are:
fast and bandwidth-efficient backup of ceph/rbd virtual machine images to S3 or NFS storage
backup of LVM volumes (e.g. from personal computers) to external USB disks
- Small backups
backy2 deduplicates while reading from the block device and only writes blocks once if they have the same checksum (sha512).
- Compressed backups
backy2 compresses all data blocks with respect to performance with the zstandard library.
- Encrypted backps
All data blocks are encrypted by default. Encryption is managed in integer versions, migration and re-keying procedures exist.
- Fast backups
With the help of ceph’s
rbd diff, backy2 will only read the changed blocks since the last backup. We have virtual machines with 600GB backed up in about 30 seconds with <70MB/s bandwidth.
- Continuable backups and restores
If the data backend storage is unreliable (as in storage, network, …) and backups or restores can’t finish, backy2 can continue them when the outage has ended.
- Small required bandwidth to the backup target
As only changed blocks are written to the backup target, a small (i.e. gbit) connection is sufficient even for larger backups. Even with newly created block devices the traffic to the backup target is small, because these block devices usually are full of \0 and are deduplicated before even reaching the target storage.
- As simple as cp, but as clever as backup needs to be
With a very small set of commands, good
--helpand intuitive usage, backy2 feels mostly like
cp. And that’s intentional, because we think, a restore must be fool-proof and succeed even if you’re woken up at 3am and are drunk.
And it must be hard for you to do stupid things. For example, existing files or rbd volumes will not be overwritten unless you
--force, deletion of young backups will fail per default.
- Scrubbing with or without source data against bitrod and other data loss
Every backed up block keeps a checksum with it. When backy scrubs the backup, it reads the block from the backup target storage, calculates it’s checksum and compares it to the stored checksum (and size). If the checksum differs, it’s most likely that there was an error when storing or reading the block, or by bitrod on the backup target storage.
Then, the block and the backups it belongs to, are marked ‘invalid’ and the block will be re-read for the next backup version even if
rbd diffindicates that it hasn’t been changed.
Scrubbing can also take a percentage value for how many blocks of the backup it should scrub. So you can statistically scrub 16% each day and have a full scrub each week (16*7 > 100).
Even invalid backups can be restored!
- Fast restores
With supporting block storage (like ceph/rbd), a sparse restore is possible. This means, sparse blocks (i.e. blocks which “don’t exist” or are all \0) will be skipped on restore.
- Parallel: backups while scrubbing while restoring
As backy2 is a long-running process, you will of course not want to wait until something has finished. So there are very few places in backy where a global lock will be applied (especially on a very rarely used full cleanup which you can kill at any time to release the lock).
So you can scrub, backup and restore (multiple times each) on the same machine.
- Does not flood your caches
When reading large pieces of data on linux, often buffers/caches get filled with this data (which in case of backups is essentially only needed once). backy2 instructs linux to immediately forget the data once it’s processed.
- Backs up very large volumes RAM- and CPU efficiently
We backup multiple terabytes per vm (and this multiple times per night). backy2 typically runs in <1GB of RAM with these volume sizes. RAM usage depends mostly on simultaneous reads/writes which are configured through
backy.cfg. We have seen ~16GB of RAM usage with large configured queues for 200TB images and a backup performance of Ø350MB/s to an external s3 storage.
- backups can be directly mounted
backy2 brings it’s own fuse service. So a simple linux command makes backups directly mountable - even on another machine:
root@backy2:~# backy2 fuse /mnt
And on another terminal:
root@backy2:~# ls -la /mnt/by_version drwx------ 0 root root 0 Mai 3 16:14 0c44841a-8d47-11ea-8b2d-3dc6919c2aca drwx------ 0 root root 0 Mai 3 16:14 60ae794e-8d46-11ea-8b2d-3dc6919c2aca drwx------ 0 root root 0 Mai 3 16:14 9d8cfe80-8d46-11ea-8b2d-3dc6919c2aca root@backy2:~# ls -la /mnt/by_version_uid/9d8cfe80-8d46-11ea-8b2d-3dc6919c2aca -rw------- 1 root root 280M Mai 3 14:01 data -rw------- 1 root root 0 Mai 3 14:01 expire -rw------- 1 root root 9 Mai 3 14:01 name -rw------- 1 root root 0 Mai 3 14:01 snapshot_name -rw------- 1 root root 51 Mai 3 14:01 tags -rw------- 1 root root 5 Mai 3 14:01 valid root@backy2:~# cat /mnt/by_version_uid/9d8cfe80-8d46-11ea-8b2d-3dc6919c2aca/name sometest1 root@backy2:~# mount /mnt/by_version_uid/9d8cfe80-8d46-11ea-8b2d-3dc6919c2aca/data /mnt You get the idea. The data file (and resulting partitions, mounts) read/write! Writing to them will write to a temporary local file. The original backup version is *not* modified! This means, you may even boot a VM from this file from a remote backup.
- Automatic tagging of backup versions
You can tag backups with your own tags depending on your usecase. However, backy2 also tags automatically with these tags:
b_daily b_weekly b_monthly
It has a clever algorithm to detect how long the backup for any given image and this tag is ago and then tags again with the given tag. So you’ll see a b_weekly every 7 days (if you keep these backups).
- Prevents you from doing something stupid
By providing a config-value for how old backups need to be in order to be able to delete them, you can’t accidentially delete very young backups.
backy protectyou can protect versions from being deleted. This is very important when you need to restore a version which is suspect to be deleted within the next hours. During restore a lock will prevent deletion, however, by protecting it, it cannot be deleted until you decide that it’s not needed anymore.
Also, you’ll need
--forceto overwrite existing files or volumes.
- Easy installation
Currently under ubuntu 18.04, you simply install the .deb. Please refer to Installation for a detailed install process.
- Free and Open Source Software
Anyone can review the source code and audit security and functionality. backy2 is licensed under the LGPLv3 license (License).
- Quick Start
- backy2 configuration
- backy2 Administration guide
- backy2 data layout